« previous next »
Pages: [1]   Go Down

Author Topic: Water pump!  (Read 4388 times)

Offline Reckless

  • AKA Frankeu
  • Super Hero Member
  • *****
  • Posts: 2734
  • Karma: +0/-0
Water pump!
« on: April 11, 2011, 06:38:12 AM »
  This isn't the first time I replaced one but the first time on this motor. Dropped the lower unit with no problems. Taking pump housing off one of the bolts shears off. This isn't good. Sprayed it down with penetrating oil. Let it soak. Tried an easy out with no luck. My previous job I had lots of experience removing broken studs, bolts, taps etc. Figure I had 3 choices. Open the hole up and either use a heli-coil, JB Weld or open the hole up more, tap it, lock tight a stud in then grind it off flush, drill and tap that to the correct size. Going to try the JB Weld first. If I can torque it the same as the other 3 bolts I will let it go. If not will go with one of the other options. Will keep you up to date on my success or failure. Anyone have any other ideas would like to hear them.  :headscra:
Logged

Offline Salty Dog

  • Super Hero Member
  • *****
  • Posts: 3961
  • Karma: +0/-0
Re: Water pump!
« Reply #1 on: April 11, 2011, 07:22:59 AM »
Looks like you've got all the bases covered .
Logged

Offline Hunter 2

  • RFA-NJ Member
  • Super Hero Member
  • *****
  • Posts: 12156
  • Karma: +0/-0
  • 36' Topaz Express "Hallie Loren"
Re: Water pump!
« Reply #2 on: April 11, 2011, 08:01:48 AM »
The only thing I can add is to speak to a pro like maritime Matt. Maybe send him a Personal message would not hurt.
Logged
Eddie "Hunter 2"
36' Topaz "Hallie Loren"    Charter boat sailing from Wagners Marina, Keyport NJ


 Life is short, Fish Hard.

Offline Reckless

  • AKA Frankeu
  • Super Hero Member
  • *****
  • Posts: 2734
  • Karma: +0/-0
Re: Water pump!
« Reply #3 on: April 11, 2011, 12:55:40 PM »
 Update. Drilled and tapped the JB Weld material. Put the pump back together. Seemed to be able to tightened it up pretty good. 
Logged

Offline IrishAyes

  • Fishing At It's Finest
  • Admin
  • Super Hero Member
  • *****
  • Posts: 17408
  • Karma: +0/-0
Re: Water pump!
« Reply #4 on: April 11, 2011, 01:12:30 PM »
Good job Frank. Hope it hold up for you. Sounds like it will t^
Logged
Captain Joe of the Irish Ayes

May the holes in your net be no larger than the fish in it.  ~Irish Blessing

Offline Scott G.

  • Super Hero Member
  • *****
  • Posts: 3594
  • Karma: +0/-0
  • Fish out of Keyport
Re: Water pump!
« Reply #5 on: April 11, 2011, 02:05:16 PM »
 t^   Good Luck With The Repair   t^
Logged
Fishing, with me, has always been an excuse to drink in the daytime.

Offline Hunter 2

  • RFA-NJ Member
  • Super Hero Member
  • *****
  • Posts: 12156
  • Karma: +0/-0
  • 36' Topaz Express "Hallie Loren"
Re: Water pump!
« Reply #6 on: April 11, 2011, 06:03:49 PM »
That should work fine, JB weld is good stuff.
Logged
Eddie "Hunter 2"
36' Topaz "Hallie Loren"    Charter boat sailing from Wagners Marina, Keyport NJ


 Life is short, Fish Hard.

Offline Reckless

  • AKA Frankeu
  • Super Hero Member
  • *****
  • Posts: 2734
  • Karma: +0/-0
Re: Water pump!
« Reply #7 on: April 11, 2011, 06:24:08 PM »
 Thanks for all the support!!!  slt Lower unit is back on. Have to put her in the tank and run it awhile.
Logged

Offline Fishin Dude

  • Super Hero Member
  • *****
  • Posts: 4526
  • Karma: +0/-0
  • FISH CONTROL MY BRAIN
Re: Water pump!
« Reply #8 on: April 11, 2011, 09:13:32 PM »
Sounds like it will work. With three origional tight, even just a little grip on the fourth should be enough. I don't see it as a problem. Good Luck <'((((><
Logged
I've spent most of my life fishing, the rest I've just wasted     <'((((><

Offline Maritime Matt

  • Sponsor
  • Hero Member
  • *****
  • Posts: 688
  • Karma: +0/-0
  • Maritime Skiff 20' Pioneer Pilothouse USCG Lic
    • TASKMARINE.COM
Re: Water pump!
« Reply #9 on: April 14, 2011, 10:37:48 PM »
Frank, it happens. Glad to see you tackled it. Wait til you see what those 4 little parts that were tie wrapped in the box cost. When ya get a tight bolt, always use a small ratchet so there is very little leverage to turn and break it. Tap the bolt head. Turn to loosen it a bit. Turn to tighten it. Back and forth, gently. Tap it a few more times. PB Blaster is great shop stuff.
Some times it just breaks. Stainless is soft stuff.
Matt
Logged

  WWW.TASKMARINE.COM     Marine SERVICE, Parts & More

Offline Reckless

  • AKA Frankeu
  • Super Hero Member
  • *****
  • Posts: 2734
  • Karma: +0/-0
Re: Water pump!
« Reply #10 on: April 15, 2011, 04:11:42 AM »
  That bolt broke off to easy! All is good now!  slt
Logged

Offline L.T.

  • AKA Laker Taker
  • Super Hero Member
  • *****
  • Posts: 1020
  • Karma: +0/-0
Re: Water pump!
« Reply #11 on: April 15, 2011, 07:39:33 AM »
10-4 on the P-B Blaster, Great stuff  t^
Logged
Forgive your enemy but, remember the bastard's name.
Pages: [1]   Go Up
« previous next »
 

NJSFlogofinal1

BSX

terrafin

Heavy Duty truck Parts On Line

Web Site Design

JSBSE_430x80.png

Know Before You Go

Local Weather | Marine Bouy Weather | Inshore Forecast | Offshore Forecast | Interactive Wind Charts | Tide Charts | Sea Surface Temps | Chlorophyll Concentrates | Online Chart Viewer

-

new jersey marine weather forecastterrafin

-