Author Topic: can u help me?  (Read 2696 times)

Offline BigAl13

  • Super Hero Member
  • *****
  • Posts: 6026
  • Karma: +0/-0
  • Fish out of Keyport
can u help me?
« on: October 20, 2010, 06:57:46 PM »
I have a bottom line fishfinder I can't figure out how to mount the transducer its shaped like an ovalish octagan and the mountig brakets are two L's with two holes on each side of the bracket I can't figure out how the connect please help
Its better to sit in a boat and think about God, than to sit in a church and think about fishing.


Offline Bucktail

  • Just a Jig-alo
  • Admin
  • Super Hero Member
  • *****
  • Posts: 12628
  • Karma: +0/-0
  • Have jigs. Will travel.
    • NJ Saltwater Fishing Tackle
Re: can u help me?
« Reply #1 on: October 20, 2010, 10:30:37 PM »
Al,

It might be helpful if you can post a pic of the bracket and transducer.  I don't think this should be too difficult for some of our members here to figure out for you. t^


Offline Fishin Dude

  • Super Hero Member
  • *****
  • Posts: 4526
  • Karma: +0/-0
  • FISH CONTROL MY BRAIN
Re: can u help me?
« Reply #2 on: October 21, 2010, 01:17:40 PM »
Does it look similar to this? Remember not to tighten the bolt that holds the transducer to the brackets too tight. It needs to be firm  needs to be able to "kick up" in the event it strikes an object. This prevents the transducer and bracket from damage. The screws or bolts holding the brackets to the transom need to be sealed with 5200 or the equivalent, and be tight, or it will leak/fall off.  <'((((><
I've spent most of my life fishing, the rest I've just wasted     <'((((><

Offline Andys Delight

  • Super Hero Member
  • *****
  • Posts: 1847
  • Karma: +0/-0
Re: can u help me?
« Reply #3 on: October 21, 2010, 03:40:24 PM »
Does it look similar to this? Remember not to tighten the bolt that holds the transducer to the brackets too tight. It needs to be firm  needs to be able to "kick up" in the event it strikes an object. This prevents the transducer and bracket from damage. The screws or bolts holding the brackets to the transom need to be sealed with 5200 or the equivalent, and be tight, or it will leak/fall off.  <'((((><

Actually, I'd recommend using 4200.  4200 will do the job just as well and if he ever upgrades he can take this one off with some elbow grease.  If he seals it with 5200 it will become a permanent fixture to the boat.   chrz
The cure for everything is salt water: sweat, tears, and the sea.


Offline Fishin Dude

  • Super Hero Member
  • *****
  • Posts: 4526
  • Karma: +0/-0
  • FISH CONTROL MY BRAIN
Re: can u help me?
« Reply #4 on: October 21, 2010, 04:09:27 PM »
I use it to seal screws, bolts, etc not actually as a glue. Just a few dabs and it's sealed. I do prefer 5200 over 4200 for the faster curing time, both are pretty tough. I know a guy who uses silicone on everything,  but I like something stronger for use below the waterline.
I've spent most of my life fishing, the rest I've just wasted     <'((((><

Offline IrishAyes

  • Fishing At It's Finest
  • Admin
  • Super Hero Member
  • *****
  • Posts: 17408
  • Karma: +0/-0
Re: can u help me?
« Reply #5 on: October 21, 2010, 05:16:22 PM »
I also use 5200. I have changed transducers at least a half dozen times on my boat and the 5200 is not as 'permanent' as it is claimed to be. As FishinDude said, for this purpose it is more of a sealer than a glue.

You probable can't go wrong using either of the two.
Captain Joe of the Irish Ayes

May the holes in your net be no larger than the fish in it.  ~Irish Blessing

Offline Fishin Dude

  • Super Hero Member
  • *****
  • Posts: 4526
  • Karma: +0/-0
  • FISH CONTROL MY BRAIN
Re: can u help me?
« Reply #6 on: October 25, 2010, 12:53:07 PM »
BigAl13, ever get the transducer hooked up? <'((((><
I've spent most of my life fishing, the rest I've just wasted     <'((((><


Offline BigAl13

  • Super Hero Member
  • *****
  • Posts: 6026
  • Karma: +0/-0
  • Fish out of Keyport
Re: can u help me?
« Reply #7 on: October 26, 2010, 07:05:53 AM »
No not yet though i finally found a picture of it. Now I can't find the brackets I put them in such a good place I don't know where they are.
Its better to sit in a boat and think about God, than to sit in a church and think about fishing.

 

NJSFlogofinal1

BSX

terrafin

Heavy Duty truck Parts On Line

Web Site Design

rfasig.png

Know Before You Go

Local Weather | Marine Bouy Weather | Inshore Forecast | Offshore Forecast | Interactive Wind Charts | Tide Charts | Sea Surface Temps | Chlorophyll Concentrates | Online Chart Viewer

-

new jersey marine weather forecastterrafin

-