« previous next »
Pages: [1]   Go Down

Author Topic: $3.00 rod chuck  (Read 7424 times)

Offline SurfJockey

  • Super Hero Member
  • *****
  • Posts: 3913
  • Karma: +0/-0
    • Facebook
$3.00 rod chuck
« on: March 28, 2011, 10:26:20 AM »
With the project I'm working on, I needed to devise a way to attach a rod to my rotisserie motor, and this is what I came up with.  Cost about 3 bucks and is made up of a 2" threaded PVC adapter, a 2" cleanout cap, 3 thumbscrews, a 1/4" bolt, 2 nuts, and 2 washers.  The rotisserie motor has a square drive in it, so I had to take the hex head bolt to the grinder and square it off to fit.  The thumbscrews were tapped into the adapter to center the rod during spinning.  Should work well and was very cheap to make. 
Logged
IBSP #1-4150 NJBBA #4753 - Red 2007 Ford Explorer Sport-Trac

Offline Bucktail

  • Just a Jig-alo
  • Admin
  • Super Hero Member
  • *****
  • Posts: 12628
  • Karma: +0/-0
  • Have jigs. Will travel.
    • NJ Saltwater Fishing Tackle
Re: $3.00 rod chuck
« Reply #1 on: March 28, 2011, 10:36:36 AM »
Nice work. t^
Logged

Offline Scott G.

  • Super Hero Member
  • *****
  • Posts: 3594
  • Karma: +0/-0
  • Fish out of Keyport
Re: $3.00 rod chuck
« Reply #2 on: March 28, 2011, 11:03:11 AM »
 t^  YOU DA MAN JASON   t^
Logged
Fishing, with me, has always been an excuse to drink in the daytime.

Offline Kenny

  • Super Hero Member
  • *****
  • Posts: 7595
  • Karma: +0/-0
  • My Fishing Buddie !
Re: $3.00 rod chuck
« Reply #3 on: March 28, 2011, 12:02:44 PM »
Nice job Jason aka Macgyver  t^
Logged

Offline SurfJockey

  • Super Hero Member
  • *****
  • Posts: 3913
  • Karma: +0/-0
    • Facebook
Re: $3.00 rod chuck
« Reply #4 on: March 28, 2011, 12:13:08 PM »
 rofla
I tried to use a cantaloupe, 3 dimes, and a pair of my wife's panties, but it didn't work too well.  I had to suck it up and go to Home Depot. 
Logged
IBSP #1-4150 NJBBA #4753 - Red 2007 Ford Explorer Sport-Trac

Offline Scott G.

  • Super Hero Member
  • *****
  • Posts: 3594
  • Karma: +0/-0
  • Fish out of Keyport
Re: $3.00 rod chuck
« Reply #5 on: March 28, 2011, 12:13:53 PM »
 rofla hhppy rofla
Logged
Fishing, with me, has always been an excuse to drink in the daytime.

Offline Luna Sea 5

  • Admin
  • Super Hero Member
  • *****
  • Posts: 12104
  • Karma: +0/-0
  • Nick (Luna Sea 5)
    • My Facebook Profile
Re: $3.00 rod chuck
« Reply #6 on: March 28, 2011, 01:06:29 PM »
 t^
Logged
Fish out of Toms River NJ.
Call Nick for open boat, 973-417-5756, or on Channel 68.

Team Luna Sea 6

Offline IrishAyes

  • Fishing At It's Finest
  • Admin
  • Super Hero Member
  • *****
  • Posts: 17408
  • Karma: +0/-0
Re: $3.00 rod chuck
« Reply #7 on: March 28, 2011, 01:08:30 PM »
Nice work Jason.  slt
Logged
Captain Joe of the Irish Ayes

May the holes in your net be no larger than the fish in it.  ~Irish Blessing

Offline Wreckfish

  • Super Hero Member
  • *****
  • Posts: 1138
  • Karma: +0/-0
Re: $3.00 rod chuck
« Reply #8 on: March 28, 2011, 01:30:20 PM »
Jason,
Looks great. Some advise. Take three rubber band (one around each wing nut) and wrap around blank or whatever you are tuning. I had a similar set up and occasionly the wing nut would back up while turning overnight and your epoxy job gets ruined.  t^
Logged

Offline SurfJockey

  • Super Hero Member
  • *****
  • Posts: 3913
  • Karma: +0/-0
    • Facebook
Re: $3.00 rod chuck
« Reply #9 on: March 28, 2011, 01:43:08 PM »
Thanks for the tip Phil!  Was hoping for some of your insight on this.  My biggest fear is the whole contraption slipping off the motors drive and just sitting there, not turning.  I plan to do a test run overnight before I break out the epoxy.
Logged
IBSP #1-4150 NJBBA #4753 - Red 2007 Ford Explorer Sport-Trac

Offline Kenny

  • Super Hero Member
  • *****
  • Posts: 7595
  • Karma: +0/-0
  • My Fishing Buddie !
Re: $3.00 rod chuck
« Reply #10 on: March 28, 2011, 01:59:43 PM »
Quote from: Jason DeCarlo on March 28, 2011, 12:13:08 PM
rofla
I tried to use a cantaloupe, 3 dimes, and a pair of my wife's panties, but it didn't work too well.  I had to suck it up and go to Home Depot. 

 rofla rofla rofla rofla rofla LMAO
Logged

Offline Hunter 2

  • RFA-NJ Member
  • Super Hero Member
  • *****
  • Posts: 12156
  • Karma: +0/-0
  • 36' Topaz Express "Hallie Loren"
Re: $3.00 rod chuck
« Reply #11 on: March 28, 2011, 07:29:37 PM »
NO DUCT TAPE OR BUBBLEGUM?? 5hrug 5hrug   ;D ;D
Logged
Eddie "Hunter 2"
36' Topaz "Hallie Loren"    Charter boat sailing from Wagners Marina, Keyport NJ


 Life is short, Fish Hard.

Offline Pops Soul

  • SKIP <*}}}><
  • Super Hero Member
  • *****
  • Posts: 5384
  • Karma: +0/-0
  • SKIP <*}}}><
Re: $3.00 rod chuck
« Reply #12 on: March 28, 2011, 07:51:18 PM »
Quote from: Jason DeCarlo on March 28, 2011, 12:13:08 PM
  my wife's panties
Like the way you think Jason!  TT^ Nice going bud, Like me always a way to build it
 cheaper... t^
Logged
It's Not A Knot Until You Pull It Tight!
Pages: [1]   Go Up
« previous next »
 

NJSFlogofinal1

BSX

terrafin

Heavy Duty truck Parts On Line

Web Site Design

rfasig.png

Know Before You Go

Local Weather | Marine Bouy Weather | Inshore Forecast | Offshore Forecast | Interactive Wind Charts | Tide Charts | Sea Surface Temps | Chlorophyll Concentrates | Online Chart Viewer

-

new jersey marine weather forecastterrafin

-