Author Topic: ULTRA MINNOW MOLD  (Read 4174 times)

Offline Tom Ciuba

  • New Member
  • *
  • Posts: 1
  • Karma: +0/-0
ULTRA MINNOW MOLD
« on: February 22, 2013, 03:42:14 PM »
HI- NEW MEMBER HERE. Was wondering if anyone knows hot to make the 5-6& 8 OZ ultra minnow with a smaller than a 9/0 hook which is what the mold calls for. The 9/0 seems too big for fluke. Any ideas??? Or maybe 9/0 is the right size. Any feedback will be appreciated,THANKS Tom


Offline FishOn

  • Hero Member
  • ****
  • Posts: 586
  • Karma: +0/-0
Re: ULTRA MINNOW MOLD
« Reply #1 on: February 22, 2013, 05:47:11 PM »
You could also tie on a smaller stinger hook
Who are you to judge the life I live? I'm not perfect and I don't have to be! Before you start pointing fingers, make sure your hands are clean. - Bob Marley


Offline Kenny

  • Super Hero Member
  • *****
  • Posts: 7595
  • Karma: +0/-0
  • My Fishing Buddie !
Re: ULTRA MINNOW MOLD
« Reply #2 on: February 22, 2013, 06:11:32 PM »
Been using the 8/0 in my 5 6 and 8ozers...

Offline IrishAyes

  • Fishing At It's Finest
  • Admin
  • Super Hero Member
  • *****
  • Posts: 17408
  • Karma: +0/-0
Re: ULTRA MINNOW MOLD
« Reply #3 on: February 22, 2013, 07:30:53 PM »
I also use the 8/0 hooks. The fluke has a huge mouth so there would be no problem with one inhaling a larger hook. Besides, with the larger spros I have found that most of the hits come on the teaser that is 18" above the spro.
Captain Joe of the Irish Ayes

May the holes in your net be no larger than the fish in it.  ~Irish Blessing


Offline makokeith

  • Hero Member
  • ****
  • Posts: 883
  • Karma: +0/-0
  • Personal Best 38LBS
Re: ULTRA MINNOW MOLD
« Reply #4 on: February 22, 2013, 08:24:01 PM »
Did you guys dremmel the mold at all to get the eye on the 8/0 to sit right?
  Picked this mold up a few months ago but have only poured a few for swing hooks. I have stainless wire that is the perfect size that I form to fit in the mold.
  But as mentioned , assist hooks and a huge strip bait is what I plan on doing with the spro grub up top.
Keith
Franklin, N.J.
Proud member of the I.B.E.W. local 827

MAKO 250wa twin 150 E-tecs
  Happily fishing out of Atlantic Highlands Municiple Marina.

Offline Kenny

  • Super Hero Member
  • *****
  • Posts: 7595
  • Karma: +0/-0
  • My Fishing Buddie !
Re: ULTRA MINNOW MOLD
« Reply #5 on: February 23, 2013, 12:56:05 PM »
I did not have to modify the 5 thru 8oz mold to fit the 8/0 hooks....fit like a champ  t^

 

NJSFlogofinal1

BSX

terrafin

Heavy Duty truck Parts On Line

Web Site Design

rfasig.png

Know Before You Go

Local Weather | Marine Bouy Weather | Inshore Forecast | Offshore Forecast | Interactive Wind Charts | Tide Charts | Sea Surface Temps | Chlorophyll Concentrates | Online Chart Viewer

-

new jersey marine weather forecastterrafin

-